Header
IN SHORT:
HC Plus by HCigar
HC Plus by HCigar

HC Plus by HCigar

A nice atomizer, Simple, effective and practical.

This product has been loaned by our sponsor VapExperience (http://www.vapexperience.com/)

Are price is 36, 90 Euros.

 1- Commercial characteristics:

The HC Plus is a fiber atomizer that can be found at the affordable price of 38.90 euros. A rebuildable mono-resistance with a reservoir of 3.5ml

aab

2- The physical characteristics, quality and packaging:

It is rather imposing with a diameter of 23 mms, a total length of 77 mms with drip tip (supplied) and a weight of 90 grs.

It is an atomizer of very good quality, both on materials and on the machining of parts.

Two tanks are delivered with the HC Plus. One in PPMA and the other in metal. You will also find in addition four O-rings of different diameters, two fixing screws for resistance, a small Phillips screwdriver, two ready-to-use resistors, cotton and a silica bit.

The air flow ring is the only downside in these features because it tends to rotate too easily. Too bad a blocking system was not thought.

A user manual would have been useful, especially for the installation of the wick and a warning for filling.

aac

3- The characteristics of the drip tip:

A nice drip tip original by its shape, comfortable in mouth and good quality.

aad

4- Functional characteristics:

  • we have a 510 stud adjustable screw.

AAE

  • The airflow is regulated by a ring on the base of the atomizer by a hole on each side. It is possible to have one or two openings.

aaf

  • The bell is in two parts, the lower one constitutes the assembly retaining ring which fits with its seal. It has two holes (one on each side), which once in place, allow the liquid to enter to soak the wick.

aag

 

  • The top of the bell has a "standard" type chimney with the correct opening diameter.

On the top, a machined location is provided for inserting a gasket. So there is no risk of this seal moving ... everything always remains airtight.

AAHA                         aah

 

 5- Assessment in use:

I started to resist, but at the time of fixing it to the studs, I found that the holes were not at all practical. After a few twists, I got there. The ideal would have been to have other holes in the opposite direction, because the air flowing through the center of the base (so the resistance is obligatorily in the middle).

To make it simple it is more convenient to fix the legs around the screws of the studs and to tighten.

aai                  AAIA

 

Then I put my cotton.

aaj

I hesitated to know how to then place my wick. But finding that the air flow under my resistance was not flush with the plateau, but rather salient,

aak

So I just put the wick soaked and folded on the board.

aal

Then I put the ring (bottom of the chimney) taking care to align the holes of the ring with the channels of the base of the plate.

aam                   at

 

Then, I unfolded the end of the wicks to reach the edges of the channels so as not to have a massive influx of liquid during the suction.

aao          AAOA

 

I closed my atomizer and filled the tank.

For filling, it is imperative to close your air flow by sliding the ring. Otherwise, you risk major leaks through the air intake holes.

aap

Then remove the small metal cap located under the top cap, and fill.

aaq

All that remains is to completely close the atomizer, open the air supply and vape ...

Conclusion:

This atomizer is really very simple for the realization of its assembly. The rendering of flavors is undoubtedly present, its vapor is average and the opening of the air flow is limited in its diameter but quite honorable (personally I do not want more). Only the adjustment of this ring lacks support to prevent it from turning on its own.

It is a given atomizer for 23mm that I mounted on a mod in 22.6mm. The set goes well and the difference is not noticed because the precise diameter of this atomizer is 22.8mm. As for its liquid content, it is slightly lower than the 4ml announced.

 

aar

 

Voila, you know everything.

Looking forward to reading you.

Sylvie.I

Print Friendly, PDF & Email
Com Inside Bottom
Com Inside Bottom
Com Inside Bottom
Com Inside Bottom

About the Author